Plumbing Basics: An Essential for Installing a Bathtub
Plumbing Basics: An Essential for Installing a Bathtub
Blog Article
Were you trying to find advise concerning How to Install a Bathtub Yourself?
Mounting a bath tub isn't precisely rocket science, however it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably difficult project. If the old bathtub is conveniently easily accessible, the job can move rapidly; if you have to open up a wall surface to remove the old bathtub and position the brand-new tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will require an assistant to vacate the old tub and embeded in the brand-new one. Make certain you have qualified on your own for the task and also fit trying it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to consider employing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This write-up will certainly aid you mount a new tub in your restroom if you have actually currently gotten a new tub as well as do not need to alter the arrangement of your previous water pipelines.
Your devices and material checklist must consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the restricted access that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. Once the supply pipes have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location in between the tap as well as the sink. Protect the faucet in position with the producer given backnut. Once the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bath tub
Utilizing both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the tub up until the spirit level reviews level.
To install faucets, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water as well as inspect all joints and brand-new pipework for leakages and also tighten them if needed. Fill the bath tub as well as additionally examine the overflow electrical outlet and also the typical outlet for leaks.
Lastly, deal with the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub should wait up until the tub has actually been made use of at least when as this will resolve it into its final placement.
Planning for the Installment
Firstly, the sustaining framework supplied with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to prevent pressure on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack a stiff seal, triggering the water to penetrate the wall surface between the bath and also the tiling, leading to difficulties with wetness and also possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are sold in tubes and cartridges, and also can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
We hope you liked our post about Tools You Need to Install a New Bathtub . Many thanks for taking time to read our blog post. So long as you enjoyed our blog posting please remember to pass it around. Thanks so much for your time spent reading it.
Address all plumbing emergencies here. Report this page